No sign-up needed

Free ASE A1–A9 practice test

20 questions, each with a clear explanation.

Quick PracticeQuestion 1 of 20
Your progress through this set
Engine Repair (A1)Step 1 · Choose one answer

An engine has developed a light knock that is loudest at about 2,000 rpm with light throttle. The knock is not heard at a cold start and appears only once the engine is fully warm. When the technician disables the cylinder 4 fuel injector with a scan tool, the knock almost disappears; disabling any other cylinder makes no difference. Which of these is the most likely cause?

Question review

All 20 ASE A1–A9 questions with explanations

Try the set above first, then use this list to review. Each answer and explanation stays closed until you open it.

  1. Question 1 · Engine Repair (A1)

    An engine has developed a light knock that is loudest at about 2,000 rpm with light throttle. The knock is not heard at a cold start and appears only once the engine is fully warm. When the technician disables the cylinder 4 fuel injector with a scan tool, the knock almost disappears; disabling any other cylinder makes no difference. Which of these is the most likely cause?

    1. Piston slap from a worn piston skirt in cylinder 4
    2. A timing chain tensioner that bleeds down overnight
    3. Excessive oil clearance at the cylinder 4 rod bearing
    4. Too much clearance at the rear main bearing journal
    Show answer and explanation for question 1

    Correct answer: C · Excessive oil clearance at the cylinder 4 rod bearing

    A connecting rod bearing knock is a lighter knock that is often loudest under light load around 2,000 rpm, and it fades when its cylinder stops firing, because combustion no longer drives the rod against the worn bearing. That is what happened when the cylinder 4 injector was disabled. Piston slap is usually loudest on a cold engine and quiets as the piston expands, but this knock appears only when the engine is warm. A tensioner that bleeds down rattles for a few seconds at start-up and is not tied to one cylinder. A worn main bearing gives a deeper knock that disabling a single cylinder rarely silences, because cylinders on both sides of the journal load it.

    Look for this next time: A knock that fades when one cylinder is disabled points to that cylinder's connecting rod bearing.

  2. Question 2 · Engine Repair (A1)

    An engine with coil-on-plug ignition has a stored misfire code for cylinder 2 and a rough idle. The technician swaps the ignition coils between cylinders 2 and 3, clears the code and runs the engine. The misfire code now sets for cylinder 3, and cylinder 2 runs smoothly. What is the most likely cause?

    1. The ignition coil that was moved from cylinder 2
    2. A cracked spark plug insulator in cylinder 2
    3. A vacuum leak at the cylinder 2 intake runner
    4. A partly clogged fuel injector feeding cylinder 2
    Show answer and explanation for question 2

    Correct answer: A · The ignition coil that was moved from cylinder 2

    Swapping coils shows whether a misfire follows a part. The misfire moved to cylinder 3, which now carries the coil that was on cylinder 2, so the fault traveled with that coil. A cracked spark plug insulator, a vacuum leak at the intake runner and a clogged injector all stay with cylinder 2 when only the coils are swapped, so if any of them were the cause, the misfire would have stayed on cylinder 2. Before replacing the coil, confirm it with a coil test or by swapping it back, as the service information directs.

    Look for this next time: When a misfire moves with a swapped coil, the coil is at fault; when it stays put, check that cylinder's plug, fuel and compression.

  3. Question 3 · Automatic Transmission/Transaxle (A2)

    A vehicle with a torque converter automatic transmission shudders at about 45 mph under light throttle, as if driving over rumble strips. Scan data show the torque converter clutch (TCC) applying at that moment, and the shudder stops when the driver taps the brake pedal and the TCC releases. The scan tool shows no misfire counts. Which of these is the most likely cause?

    1. A worn inner CV joint on the front axle
    2. A drive shaft that is out of balance
    3. Worn engine mounts that pass engine vibration to the body
    4. A converter clutch that chatters each time it applies
    Show answer and explanation for question 3

    Correct answer: D · A converter clutch that chatters each time it applies

    The shudder comes only while the TCC is applying and stops the moment the brake switch releases it, which ties the symptom to the converter clutch itself, often to worn friction material or fluid that has lost its friction properties. With no misfire counts, an engine misfire is not imitating the shudder. An out-of-balance drive shaft and a worn inner CV joint would vibrate at that road speed whether or not the TCC is applied. Worn engine mounts usually show up as a clunk or a vibration when the load changes, not as a shudder that ends when the converter clutch releases.

    Look for this next time: A shudder that starts with TCC apply and stops when the TCC releases points to the converter clutch.

  4. Question 4 · Automatic Transmission/Transaxle (A2)

    After a transmission is reinstalled, the engine will not crank with the shift lever in PARK but cranks normally in NEUTRAL. With the lever in PARK, the gear indicator on the dash flickers between P and R. What should the technician do first?

    1. Replace the starter relay, then retest in PARK
    2. Check the shift cable and range sensor adjustment
    3. Replace the ignition switch, which controls the crank signal
    4. Reprogram the transmission control module software
    Show answer and explanation for question 4

    Correct answer: B · Check the shift cable and range sensor adjustment

    The engine cranks in NEUTRAL, so the starter, its relay and the ignition switch can all complete the crank circuit. What fails is the PARK signal. A gear display that flickers between P and R with the lever in PARK shows the transmission range sensor reading a position between gears, which is what happens when the shift cable or the sensor is out of adjustment after the transmission goes back in. Replacing the starter relay or the ignition switch ignores that both already work in NEUTRAL. Reprogramming the transmission control module comes, if ever, only after the range input it receives is correct.

    Look for this next time: Cranking in NEUTRAL but not PARK, with a wrong gear display, points to the shift cable or range sensor adjustment.

  5. Question 5 · Manual Drive Train and Axles (A3)

    A rear-wheel-drive car with a five-speed manual transmission grinds only when shifting into third gear, even when the driver shifts slowly. The clutch releases fully, and every other gear, including reverse from a stop, engages quietly. Which of these is the most likely cause?

    1. A clutch disc that keeps dragging with the pedal held down
    2. A weak detent spring on the 3–4 shift rail
    3. A pilot bearing that is worn out and running dry
    4. A worn blocking ring on the synchronizer for third gear
    Show answer and explanation for question 5

    Correct answer: D · A worn blocking ring on the synchronizer for third gear

    A synchronizer's blocking ring brings the gear and the shaft to the same speed before the sleeve engages. When only one gear grinds and the clutch releases fully, the synchronizer for that gear is the usual suspect, here the third-gear blocking ring. A dragging clutch disc would make every gear hard to engage, including reverse from a stop. A weak detent spring lets the transmission jump out of gear rather than grind going in. A worn or dry pilot bearing makes noise with the pedal down, not clash in a single gear.

    Look for this next time: Gear clash in one gear only, with a clutch that releases fully, points to that gear's synchronizer.

  6. Question 6 · Manual Drive Train and Axles (A3)

    Soon after one damaged tire on an all-wheel-drive SUV was replaced with a new tire of the same size, the driver reports binding and tire scrub in tight, low-speed turns. The other three tires are the original set and are well worn. What should the technician check first?

    1. The transfer case, for a fill with the wrong fluid type
    2. Both rear wheel bearings for roughness
    3. The new tire's circumference against the other three
    4. The front differential for low or burnt fluid
    Show answer and explanation for question 6

    Correct answer: C · The new tire's circumference against the other three

    Many all-wheel-drive systems let the center coupling or differential slip briefly when the front and rear axles turn at different speeds in a turn. A new tire has a larger rolling circumference than three worn ones, so its wheel turns at a different speed all the time, and the coupling is forced to slip constantly, which can cause binding in tight turns and wear the coupling. ASE's A3 task list includes checking tires for matching circumference for this reason. Wrong or low fluid in the transfer case or front differential and rough wheel bearings can all cause noise, but none of them began with the tire replacement.

    Look for this next time: On an all-wheel-drive vehicle, a tire whose circumference doesn't match the others can make the center coupling slip and bind.

  7. Question 7 · Suspension and Steering (A4)

    After a hydraulic power steering pump is replaced, the system groans when the steering wheel is turned, and the fluid in the reservoir looks foamy. The fluid is the type the manufacturer specifies, and there are no leaks. What should the technician do next?

    1. Bleed the trapped air as the service information directs
    2. Replace the new pump again, since a new pump should be quiet
    3. Top off the reservoir until the fluid reaches the cap
    4. Tighten the steering gear's sector lash adjustment
    Show answer and explanation for question 7

    Correct answer: A · Bleed the trapped air as the service information directs

    Foamy fluid and a groan right after a pump replacement mean air is trapped in the system, and ASE's A4 task list includes flushing, filling and bleeding the power steering system. Bleeding procedures differ by vehicle, so follow the one in the service information. Replacing the new pump again treats the noise without removing the air that causes it. Filling the reservoir to the cap overfills it, and the extra fluid can foam and overflow as it heats. Sector lash is an adjustment on a non-rack steering gear for free play, and it has nothing to do with aerated fluid.

    Look for this next time: Foamy fluid and groaning after power steering work mean trapped air; bleed it the way the service information says.

  8. Question 8 · Suspension and Steering (A4)

    A MacPherson strut assembly is on the bench so the technician can replace the strut and its upper mount. The coil spring is still installed on the strut. What must be done before the nut on top of the strut rod is loosened?

    1. Clamp the polished rod with locking pliers
    2. Compress the spring with a strut spring compressor
    3. Loosen the nut in short bursts with an impact wrench
    4. Mark the strut's position on the steering knuckle
    Show answer and explanation for question 8

    Correct answer: B · Compress the spring with a strut spring compressor

    With the spring installed, the nut on the strut rod is what holds the spring's stored energy, so the spring must be compressed with a strut spring compressor until the upper mount is free of spring pressure before that nut is loosened. Loosening it with an impact wrench, in short bursts or not, can let the spring and mount come apart violently. Gripping the polished rod with locking pliers scars the surface the strut seal rides on. Marking the strut's position on the knuckle helps keep the alignment close, but it belongs before the strut comes off the vehicle and does nothing to make the spring safe.

    Look for this next time: Never loosen a strut rod nut until the coil spring is compressed and holding its own tension.

  9. Question 9 · Brakes (A5)

    Federal Motor Vehicle Safety Standard 116 requires DOT 3 brake fluid to have an equilibrium reflux boiling point of at least 401°F when tested new and at least 284°F in its 'wet' test, which is run after the fluid sample has been humidified. What should a technician take from the lower wet figure?

    1. DOT 3 fluid can be topped off with silicone DOT 5 fluid
    2. The wet figure applies only to cars driven in rainy climates
    3. Moisture absorbed over time lowers the fluid's boiling point
    4. New fluid boils sooner than aged fluid
    Show answer and explanation for question 9

    Correct answer: C · Moisture absorbed over time lowers the fluid's boiling point

    FMVSS 116 measures the wet boiling point after humidifying the sample because glycol-based brake fluids such as DOT 3 absorb moisture in service, and that water lowers the boiling point. Old fluid can therefore boil during hard braking and leave a spongy or fading pedal, which is one reason manufacturers set brake fluid replacement intervals. The wet test has nothing to do with the climate a car is driven in. DOT 5 is a silicone-based grade with its own requirements, so the figures do not make it a top-off fluid for DOT 3. New fluid has the higher, dry boiling point, not the lower one.

    Look for this next time: Glycol brake fluid absorbs moisture, and FMVSS 116's lower wet boiling point shows how much that can cost.

  10. Question 10 · Brakes (A5)

    A car has rear disc brakes with electric parking brake motors mounted on the calipers. The technician is about to replace the rear pads. Before the caliper pistons are pushed back to make room for the new pads, what should be done?

    1. Apply the parking brake so the pistons stay in place
    2. Press each piston back with a large C-clamp, motors still connected
    3. Disconnect the battery so the motors release the pistons
    4. Retract the motors with a scan tool or the maker's procedure
    Show answer and explanation for question 10

    Correct answer: D · Retract the motors with a scan tool or the maker's procedure

    On calipers with electric parking brake motors, the motor drives a spindle that holds the piston out, so the piston cannot be pushed back until the motor has retracted. ASE's A5 task list says to retract integral and electronic parking brake caliper pistons according to the manufacturer's specifications, which usually means a scan tool service mode or a switch sequence the maker publishes. Forcing the pistons back with a C-clamp against the spindle can damage the motor or the caliper. Applying the parking brake drives the pistons outward, the opposite of what is needed, and disconnecting the battery leaves the motors where they are.

    Look for this next time: Retract an electric parking brake with the manufacturer's service procedure before pushing rear caliper pistons back.

  11. Question 11 · Electrical/Electronic Systems (A6)

    A car's battery goes flat after the car sits for three days. With an ammeter connected in series at the battery and all modules asleep, the key-off draw is 420 mA. Pulling fuses one at a time shows that the draw falls to 25 mA, within the manufacturer's limit, only when the fuse for the trunk and cargo lamps is removed. What should the technician do next?

    1. Find the load left on in that circuit, such as a lamp held on by its switch
    2. Replace the battery, because a draw of 420 mA is normal for a modern car
    3. Test the alternator diodes for reverse current leakage
    4. Replace the body control module that controls the trunk lamps
    Show answer and explanation for question 11

    Correct answer: A · Find the load left on in that circuit, such as a lamp held on by its switch

    Pulling fuses one at a time after the modules are asleep isolates a key-off drain: the circuit whose fuse brings the draw back within the manufacturer's limit holds the fault. Here that is the trunk and cargo lamp circuit, so the next step is to find what keeps a load on in it, such as a lamp held on by a stuck or misadjusted switch. The battery is the victim, and 420 mA is far above the 25 mA the car draws without that circuit. A leaking alternator diode would keep drawing current whichever lamp fuse is pulled. Replacing the body control module would be premature while one lamp circuit accounts for the whole excess and its switches and lamps are untested.

    Look for this next time: When pulling one fuse brings a key-off draw back within the limit, look for the load left on in that circuit.

  12. Question 12 · Electrical/Electronic Systems (A6)

    A technician is jump-starting a car that has a dead 12-volt battery, using a booster battery. The positive cable is already clamped to both positive posts, and one end of the negative cable is clamped to the booster battery's negative post. Where should the last clamp go?

    1. The dead battery's negative post, for the shortest circuit
    2. An unpainted engine ground on the disabled car, away from the battery
    3. The disabled car's starter motor feed terminal
    4. A bare metal point on the booster car's own engine
    Show answer and explanation for question 12

    Correct answer: B · An unpainted engine ground on the disabled car, away from the battery

    The last connection is the one most likely to spark, and a battery, especially one being charged, can give off explosive hydrogen gas. So the final clamp goes on a solid, unpainted metal ground on the disabled car's engine, or on the ground point the manufacturer designates, away from the battery. Clamping the dead battery's negative post puts that spark right at the battery. The starter feed terminal is a positive connection, so a negative clamp there would short the booster. A point on the booster car's own engine would leave both ends of the negative cable on the booster side, so the circuit through the disabled car would never be completed.

    Look for this next time: Make the final jump-start connection to a ground on the disabled vehicle, away from its battery.

  13. Question 13 · Electrical/Electronic Systems (A6)

    On a car with power door locks, every door locks and unlocks from each switch and from the key fob except the right rear, which does nothing. At the right-rear actuator connector, a test light shows battery voltage on one wire and ground on the other when LOCK is pressed, with the polarity reversed when UNLOCK is pressed. Which of these is the most likely cause?

    1. A blown fuse in the door lock circuit
    2. A failed door lock switch on the driver's door
    3. A body control module with a failed lock output driver
    4. A failed right-rear actuator or a loose lock rod
    Show answer and explanation for question 13

    Correct answer: D · A failed right-rear actuator or a loose lock rod

    The test light shows the command reaching the right-rear actuator connector with the correct polarity for both LOCK and UNLOCK, so everything upstream of that connector works: the fuse, the switches, the fob receiver and the module's outputs. If the lock still doesn't move, the fault is the actuator itself or the linkage between it and the latch, such as a lock rod that came off its clip. A blown fuse or a failed driver's switch would affect more than one door, and the fob still works on the other doors. A failed module output could not deliver the voltage the test light shows.

    Look for this next time: When the correct command reaches a lock actuator but nothing moves, the actuator or its linkage is at fault.

  14. Question 14 · Heating and Air Conditioning (A7)

    A car with no heater control valve blows only lukewarm air with the temperature set to full heat. The engine is at normal operating temperature, the coolant is full, and the blend door moves through its full travel. With the engine running, the heater inlet hose is hot but the outlet hose is much cooler. Which of these is the most likely cause?

    1. A heater core partly blocked by scale or debris
    2. A thermostat stuck open, keeping the engine cool
    3. A blend door actuator stuck in the full-cold position
    4. An A/C system that is low on refrigerant
    Show answer and explanation for question 14

    Correct answer: A · A heater core partly blocked by scale or debris

    Hot coolant entering the heater core and much cooler coolant leaving it means too little coolant is flowing through the core, and with no heater control valve in the circuit, a partly blocked core is the likely restriction. A thermostat stuck open would keep the engine below operating temperature, and both heater hoses would feel lukewarm. A blend door stuck at full cold would leave both hoses hot while the air stays cool, and this door moves through its full travel. The A/C refrigerant charge does not change how much heat the heater core gives off.

    Look for this next time: A large temperature drop between the heater hoses points to low coolant flow through the heater core.

  15. Question 15 · Heating and Air Conditioning (A7)

    An A/C system with a fixed orifice tube is opened to replace a leaking evaporator, and the service information calls for replacing the component that holds the desiccant. Which component is that on this system?

    1. The receiver-drier at the condenser outlet
    2. The muffler on the compressor discharge line
    3. The accumulator at the outlet of the evaporator
    4. The high-pressure relief valve on the compressor
    Show answer and explanation for question 15

    Correct answer: C · The accumulator at the outlet of the evaporator

    Orifice tube systems keep the desiccant in an accumulator on the low side, at the evaporator outlet, where it also holds back liquid refrigerant so that vapor returns to the compressor. A receiver-drier at the condenser outlet does the drying job on systems with an expansion valve, not on this one. The discharge-line muffler only quiets compressor pulses, and the high-pressure relief valve vents refrigerant if pressure climbs too high, so neither holds desiccant. ASE's A7 task list covers replacing the receiver-drier, the accumulator-drier or the desiccant.

    Look for this next time: Orifice tube systems keep their desiccant in the accumulator; expansion valve systems use a receiver-drier.

  16. Question 16 · Heating and Air Conditioning (A7)

    In a car with manual climate controls and a resistor-type blower speed control, the blower runs normally on its highest speed but does not run at all on the three lower speeds. Which of these is the most likely cause?

    1. A blown fuse in the blower motor feed circuit
    2. An open circuit in the blower motor resistor
    3. Worn brushes inside the blower motor
    4. An open ground circuit at the blower motor
    Show answer and explanation for question 16

    Correct answer: B · An open circuit in the blower motor resistor

    On a resistor-type control, the highest speed usually bypasses the resistor block and sends full voltage to the blower, while the lower speeds route current through the resistors. When high works and every lower speed is dead, the shared path through the resistor block is open, often at its built-in thermal limiter. A blown fuse or an open blower ground would stop the blower on every speed, including high. Worn motor brushes would affect every speed rather than leave high working normally.

    Look for this next time: A blower that runs only on high points to an open blower resistor or its thermal limiter.

  17. Question 17 · Engine Performance (A8)

    A gasoline engine with variable valve timing has a crankshaft-to-camshaft position correlation code. With the cam phasers commanded to their base (parked) positions, scan data show the intake and exhaust camshafts on that bank both retarded from the crankshaft by about the same amount. The oil level and grade are correct. Which of these is the most likely cause?

    1. A sticking oil control valve on the intake phaser
    2. A knock sensor that reports no knock activity
    3. An EVAP purge valve stuck open
    4. A stretched timing chain or worn chain guides
    Show answer and explanation for question 17

    Correct answer: D · A stretched timing chain or worn chain guides

    With the phasers parked, both camshafts on the bank should sit at their base positions relative to the crankshaft. When the intake and the exhaust camshaft are both retarded by about the same amount, the part they share with the crankshaft, the timing chain, has stretched, or worn guides have let it sag or skip. A sticking oil control valve on the intake phaser would move only the intake camshaft. A knock sensor fault and an EVAP purge valve stuck open can affect idle quality and spark timing, but neither changes where the camshafts sit relative to the crankshaft.

    Look for this next time: When every camshaft on a bank is off by the same amount, look at the timing chain that drives them all.

  18. Question 18 · Engine Performance (A8)

    An engine has a stored 'system too lean' code for bank 1. At a warm idle, long-term fuel trim is +22%. At a steady 2,500 rpm with no load, long-term fuel trim drops to +3%. Which of these is the most likely cause?

    1. A weak fuel pump that falls behind at higher flow
    2. A fuel injector leaking into a bank 1 cylinder
    3. An intake vacuum leak after the mass airflow sensor
    4. A catalytic converter restricted by melted substrate
    Show answer and explanation for question 18

    Correct answer: C · An intake vacuum leak after the mass airflow sensor

    Positive fuel trim means the engine computer is adding fuel because its oxygen or air-fuel sensors see a lean mixture. A vacuum leak after the mass airflow sensor lets in air the computer never measured. At idle that unmetered air is a large share of the total, so the trim climbs high; at 2,500 rpm the same leak is a small share of a much larger airflow, so the trim returns toward normal. A weak fuel pump does the opposite, leaning the mixture more as fuel demand rises. A leaking injector adds fuel, which pushes trims negative, and a restricted converter costs power at higher rpm rather than causing a lean idle.

    Look for this next time: Lean fuel trim that is high at idle and near normal at higher rpm usually points to unmetered air.

  19. Question 19 · Light Vehicle Diesel Engines (A9)

    A light-duty diesel pickup is losing coolant with no external leak, and white smoke with a sweet smell comes from the exhaust after start-up. Technician A says a stuck-closed EGR valve could be the cause. Technician B says a coolant leak inside the EGR cooler could be the cause. Who is right?

    1. Technician A only
    2. Technician B only
    3. Both technicians
    4. Neither technician
    Show answer and explanation for question 19

    Correct answer: B · Technician B only

    An EGR cooler runs exhaust gas through passages surrounded by engine coolant. If those passages crack, coolant enters the exhaust gas stream and leaves as white, sweet-smelling smoke, and the coolant level drops with nothing under the vehicle, so Technician B is right. Technician A is wrong: a stuck-closed EGR valve stops exhaust flow through the cooler and can set EGR flow codes, but it cannot move coolant out of the cooling system. That rules out the answers that credit Technician A alone or both technicians, and the answer saying neither is right ignores the cooler leak.

    Look for this next time: Coolant loss with no external leak and sweet white exhaust smoke on a diesel points to an internal EGR cooler leak.

  20. Question 20 · Light Vehicle Diesel Engines (A9)

    After replacing the fuel filter on a common-rail diesel pickup, the technician finds that the engine cranks at normal speed but will not start. The engine started and ran normally before the filter change, and the filter housing is not leaking. What should the technician do first?

    1. Prime the fuel system to purge the air, as specified
    2. Replace the high-pressure pump, since it has lost its prime
    3. Replace the glow plugs, which often fail as a set
    4. Run a forced DPF regeneration to clear the exhaust
    Show answer and explanation for question 20

    Correct answer: A · Prime the fuel system to purge the air, as specified

    Changing the filter lets air into the low-pressure side of the fuel system, and a common-rail system cannot build rail pressure while its supply side is full of air. ASE's A9 task list covers checking the fuel system for air and priming and bleeding it, and the manufacturer's procedure says how, for example with a hand primer, by cycling an electric lift pump, or through a bleed screw. Replacing the high-pressure pump treats trapped air as a failed part. The engine started before the filter change, so failed glow plugs are unlikely, and a DPF regeneration needs a running engine and cannot fix a no-start caused by air in the fuel.

    Look for this next time: After opening a diesel fuel system, prime and bleed the supply side before suspecting expensive parts.

Use the sample well

The rationale matters more than the score.

A short set can show you what deserves another look. A strong run shows you can reason through short diagnostic scenarios from all nine A-series tests. Twenty questions are a small sample, so the result does not predict a pass on any ASE test.

01

Answer before reviewing

Read every condition in the scenario, such as cold or warm, idle or load, one cylinder or all of them, then choose the one best answer. Read why each other option falls short.

02

Read every rationale

Confirm why the best option fits, even when you were right.

03

Follow the pattern

Use recurring misses—not one score—to choose your next focus.