Journeyman Electrician Exam guideStudy & preparation

Journeyman Electrician Exam Math: Ohm’s Law and Power Calculations

Published 6 min read3 official sources

Short answer

Choose an electrical formula by identifying the requested quantity and labeling the values you know: volts, amperes, ohms or watts. NASA Glenn gives V = IR and P = IV = I²R for a resistor, so you can rearrange those relationships before inserting numbers. The examples here assume resistive loads; code sizing, demand factors and other load conditions require the appropriate exam reference.

Which quantities should you identify before choosing a formula?

Choose your formula by writing down the quantity the question asks for and the quantities it supplies. NASA Glenn’s explanation of a resistor gives V = IR and P = IV = I²R, which connect voltage, current, resistance and power.

Use this notation consistently in your scratch work:

QuantitySymbol in these formulasUnitWhat to label in the problem
VoltageVvolt, VVoltage across the resistance being considered
CurrentIampere, ACurrent through that resistance
ResistanceRohm, ΩResistance of the load or path specified
PowerPwatt, WPower dissipated by the resistor

The letter V can represent the quantity in a formula and the volt unit after a number. In V = 240 V, the left side names the quantity and the right side gives its value. Current uses I in the formula but A after the number; do not treat those as different quantities.

NIST’s SI guide, Table 3, gives the unit relationships V = W/A and Ω = V/A. These let you check whether your arithmetic produces the requested unit. If the answer should be amperes, a result with units of ohms cannot be the answer even if the number appears among the choices.

Before calculating, write a short setup such as “find I; given V and R; use I = V/R.” This is an editorial practice method, not an additional exam rule.

How do you rearrange Ohm’s law?

Start with V = IR, then isolate the unknown before entering numbers:

FindGivenRearranged formula
VoltageCurrent and resistanceV = IR
CurrentVoltage and resistanceI = V/R
ResistanceVoltage and currentR = V/I

To get current, divide both sides of V = IR by R. To get resistance, divide both sides by I. The formula changes shape, but the relationship stays the same.

Original hypothetical example: find current. A resistive load has 240 V across a resistance of 48 Ω. What current flows through it?

  1. Identify the unknown: I, in amperes.
  2. Choose I = V/R because voltage and resistance are supplied.
  3. Substitute: I = 240 V ÷ 48 Ω = 5 A.
  4. Check by substitution: 5 A × 48 Ω = 240 V.

A reversed division, 48 ÷ 240, does not calculate current. You can catch that mistake before using a calculator: resistance divided by voltage is the opposite of the required relationship.

Now solve the same case for resistance. Suppose the problem instead supplies 240 V and 5 A. Then R = 240 V ÷ 5 A = 48 Ω. NIST’s Ω = V/A relationship confirms the unit. Multiplying volts by amperes would give power, so it would answer a different question.

Try covering the answers and solving both versions. If one direction is harder, practice that rearrangement before changing the numbers. For more problems of this kind, electrical calculation questions are planned for full journeyman electrician prep, each with an explanation.

When can you use watts equals volts times amps?

For the resistive examples here, use P = VI. NASA’s resistor explanation also gives P = I²R, so the formula you choose depends on which values the problem supplies.

Return to the hypothetical 240 V, 48 Ω load. You have already found that its current is 5 A:

  • Using voltage and current: P = 240 V × 5 A = 1,200 W.
  • Using current and resistance: P = 5² × 48 = 25 × 48 = 1,200 W.

The second line requires squaring the current. Multiplying 5 by 48 without first squaring 5 would not apply P = I²R. Keep the exponent visible in your written setup, even if your calculator can perform the entire expression at once.

Original hypothetical example: find current from power. A different resistive load dissipates 960 W at 120 V. Start with P = VI and divide both sides by V:

I = P/V = 960 W ÷ 120 V = 8 A.

Check the result by multiplying back: 120 V × 8 A = 960 W. The inverse operation helps reveal a reversed fraction or a mistyped value without requiring you to memorize another formula.

These examples assume resistive loads. Do not extend the simplified watts-equals-volts-times-amps treatment to every AC load or use the resulting current by itself as a motor-sizing answer. Read the load description and identify the applicable relationship first.

For your next practice problem, write one sentence explaining why its supplied quantities fit the formula you selected. That explanation is more useful than copying a formula list without its conditions. Once the conditions are clear, the flashcards planned for full journeyman electrician prep can keep the formulas fresh between sessions.

How do you check a voltage-drop arithmetic problem?

First identify the resistance of the path whose voltage drop is being calculated. A wiring-path resistance and a load resistance describe different parts of a problem; label the stated resistance before using it.

Original hypothetical example: A problem supplies a current of 10 A and a total resistance of 0.30 Ω for the wiring path being evaluated. It asks for that path’s voltage drop and the drop as a percentage of a stated 120 V reference.

Apply Ohm’s law to the specified path:

Voltage drop = IR = 10 A × 0.30 Ω = 3 V.

Then use the reference voltage supplied in the problem:

Percentage drop = (3 V ÷ 120 V) × 100 = 2.5%.

Keep the two requested outputs separate. The first is a voltage; the second is a percentage. Dividing 3 by 120 gives the fraction 0.025, which becomes 2.5% when multiplied by 100.

The 0.30 Ω already represents the total resistance of the path in this exercise. Do not double it or add an assumed conductor length. If another problem supplies different inputs, use its stated method and conditions rather than carrying this example’s setup into it.

The 2.5% result is arithmetic, not a universal NEC limit or a finding that an installation complies. A question asking whether a design satisfies a rule requires the applicable rule as well as the calculation. Mark that distinction in your notes before moving on.

Which calculations still need your exam’s code book?

These formulas teach how to relate the supplied electrical quantities. They do not supply a code demand factor, a conductor-selection rule or all the conditions for an equipment-sizing question.

ICC’s National Journeyman Electrician outline includes electrical theory and general load calculations in General Knowledge, with further calculation topics in its service, feeder and branch-circuit areas. That outline was checked November 11, 2026; it is an ICC example, not a statement that every jurisdiction tests the same content. Use the journeyman electrician exam format and topics guide to identify the exam you are preparing for. If ICC's exam is yours, General Knowledge practice is planned for journeyman electrician prep at launch, alongside the other eight areas.

Separate your next calculation into three decisions:

  1. What is supplied? Copy the values and units, and identify the part of the circuit they describe.
  2. What must be found? Rearrange the appropriate relationship, then calculate and substitute back to check it.
  3. Is a code decision also required? If so, locate the applicable conditions in the NEC edition your exam specifies before selecting an answer.

Use the 20 free journeyman electrician practice questions for a next practice session. For each calculation you miss, record whether the problem was the quantity, formula, arithmetic or code lookup. Then use the free journeyman electrician study plan to schedule another session on the step that needs work.

Trust the source

Official sources

Exam policies can change. Use these primary sources for the most current details.